Basic Specification

Maximum Sample Rate

5GS/s

Frequency Bandwidth

500MHz

Max. Record Length

2.5MW (model DL9040), 6.25MW (model DL9040L)

Input Channels

4 (CH1 to CH4)

Input Coupling

AC, DC, GND, DC50Ω

Input Impedance

1MΩ ±1% approx. 20pF
(when using PB500 probe, 10MΩ 2%, approx. 14pF)
50Ω ±1.5%

Voltage Axis Sensitivity
 

For 1MΩ Input:

For 50Ω Input:

Maximum Input Voltage
 

For 1MΩ Input:

For 50Ω Input:

DC Offset Max. Setting
when
probe attenuation
set to 1:1

 

2mV/div to 50mV/div:

100mV/div to 500mV/div:

1V/div to 5V/div:

2mV/div to 50mV/div:

100mV/div to 500mV/div:

Vertical (voltage) Axis Sensitivity

DC Accuracy
 

For 1MΩ Input:

For 50Ω Input:

Offset Voltage Axis
Accuracy ^{note 1}
 

2mV/div to 50mV/div:

100mV/div to 500mV/div:

1V/div to 5V/div:

Frequency Characteristics ^{notes 1,2}  For 50Ω Input and For 1MΩ Input [from probe tip when using the dedicated passive probe (PB500)].
(attenuation point -3dB when inputting a sinewave of amplitude ±2 div or equivalent)

5V/div to 10mV/div:

5mV/div to 2mV/div:

Residual Noise
Level  ^note3

0.4mV rms or 0.05 div rms, whichever is larger (typical value)
 

A/D Resolution

8-bit (25 LSB/div)

For each channel, select Full, 200MHz, 20MHz, 8MHz, 4MHz,
2MHz, 1MHz, 500kHz, 250kHz, 125kHz, 62.5kHz, 32kHz, 16kHz,
8kHz

Maximum Sampling
Rate
Real time sampling mode

Interleave mode ON:

Interleave mode OFF:

Repetitive sampling mode:

 Note 1.

Note 2.

Note 3.

Trigger Modes

Auto, Auto Level, Normal, Single, and N Single

Trigger Source

CH1 to CH4, LINE, EXT

Window Comparator

Channels CH1 to CH4, or individual channels

Trigger Types
 

Edge/State:

Width:

Event Interval

Event Cycle, Event Delay, Event Sequence

Enhanced
 

TV (NTSC), PAL, HDTV, USER/PC, SPI (3-wire, 4-wire) serial pattern

Display

Display

8.4-inch color TFT liquid crystal display

Acquisition Modes

Select from three acquisition modes: Normal, Envelope, and Average.

Other Acquisition Modes

High resolution mode, Repetitive sampling mode, Interleave mode, Interpolate mode.

Interpolate Function

Interpolates actual sampled data by up to 1000 times (or up to 2000 times in High-Res. mode) and increases the time resolution (up to 2.5 TS/s).

X - Y

Displays XY1, XY2 and T-Y simultaneously.

Accumulation

Accumulates waveforms on the display. Choose Count/Time and Inten/Color.

Snapshot

Retains the current displayed waveform on the screen.

Search and Zoom




 

Zooms the displayed waveform along the time (Horizontal Zoom) and voltage (Vertical Zoom) axes. Independent zooming factors can be applied to two zoom areas.
Search Types: Edge, Edge Qualified, State, Pulse, Pulse Qualified, Pulse State, Serial Pattern, PC (optional), SPI (optional).

History Memory
 

Cursor Measurements

Vertical, Horizontal, VT, Marker, Serial

Automatic Measurement
of Waveform Parameter
Function

 

MAX, MIN, HIGH, LOW, P-P, HIGH-LOW, +OVER, -OVER, RMS, MEAN, Sdev, IntegTY.
C.rms, C.mean, C.Sdev, C.IntegTY, (1/FREQ), FREQ, COUNT, BURST.
+WIDTH, -WIDTH, PERIOD, DUTY, RISE, FALL, DELAY

Telecom Test

Performs mask test and eye pattern measurement

Computation Functions

Computes up to eight traces (CH1 - CH4/M1 -M4)

Reference Functions

Display and analysis (computation and cursors) on up to four traces (M1-M4) of the saved waveform data.

Action-on-trigger

 

Option /B5

Built-in Printer

Option /C8

Internal Hard Disk Drive

Option /C10 and C8

Ethernet Communication

Option /F5

Bus Analysis Function (PC + SPI)

Option /F7

CAN+SPI bus analyzer

Option /F8

I²+CAN+SPI bus analyzer